Remote Programming, Boa 265, posted in the Car Security and Convenience Forum on the12volt's install bay Mobile Electronics Forums. Boa Remote Start systems can warm up your vehicle's engine with the push of a button from up to 500 feet away, and start the vehicle's climate control system. If your household is starting to be overwhelmed by the number of remotes you have, then it may be time to invest in a universal remote. Nowadays, there are remotes.

• 1 1 6 6 5 5 B B O O w w n n e e r r ’ ’ s s / / I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e. • Directed Electronics, Inc. (hereinafter 'Directed') promises to the original purchaser to repair or replace with a comparable reconditioned Directed DIY remote start unit if this Directed DIY remote start unit (hereinafter 'Unit'), excluding without limitation, any. • This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have completed the war- ranty card and mailed it to Directed Electronics, Inc.

Within 10 days after purchase to the address listed on the warranty registration card. •...4 4 5 5 © 2004 Directed Electronics, Inc. • © 2004 Directed Electronics, Inc. • Digital Multi-Meter Drill Drill Bits Screwdrivers (Phillips and Flathead) Wire Stripper Solder Iron Electrical Tape Pliers Crimping Tool note: The installation tools listed above may be optional and those required will vary depending on your vehicle.

© 2004 Directed Electronics, Inc. • Failure to properly install the remote starter may result in property damage, personal injury, or both. System maintenance The system requires no specific maintenance. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control © 2004 Directed Electronics, Inc. • Safety Check outlined in this installation guide.

If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote Paolo Conte Album. © 2004 Directed Electronics, Inc. • P P A A Y Y F F O O R R I I N N S S T T A A L L L L A A T T I I O O N N O O R R R R E E I I N N S S T T A A L L L L A A T T I I O O N N C C O O S S T T S S.. © 2004 Directed Electronics, Inc.

O O P P E E R R A A T T I I N N G G. • (-) Remote Start Activation Input Factory Alarm Disarm (+) Output to Starter Circuit (+) (30A) High Current 12V Input (+) Output to ACC1 Circuit (+) Output to IGN1 Circuit (+) (30A) High Current 12V Input Output to IGN2 Circuit © 2004 Directed Electronics, Inc.

• LED tester is not being used. Connect the Black clip to a good chassis ground. If a positive voltage source is probed, the Red LED will illuminate brightly. © 2004 Directed Electronics, Inc. • Tampering may cause unintended deployment of airbags. Siw Keygen Er. Verify that the vehicle is set to park and that the parking brake is set before beginning installation. © 2004 Directed Electronics, Inc.

• More problems are attributed to poor ground con- nections than any other cause. Take extra care to ensure the ground is a clean metal-to-metal contact and secure. NOTE: © 2004 Directed Electronics, Inc. • The color and identity of your specific vehicle wiring can be obtained at www.boasecurity.com. With the key in the OFF position, test the suspect wire.

The constant power wire will illu- minate the LED tester. © 2004 Directed Electronics, Inc. • If the LED tester extinguishes this is not an ignition wire but an accessory wire. If the wire tests correctly, solder the PINK (C) relay wire to it and cover the connection with electrical tape. © 2004 Directed Electronics, Inc.

• If the wire tests correctly, strip the insu- lation off a small portion and solder the thick ORANGE (C) relay wire to it and wrap it with electrical tape. If your vehicle requires more than one accessory contact BOA Technical Support. © 2004 Directed Electronics, Inc.

• ) and try to start the vehicle. If the vehicle does not start, the correct wire has been identified.

Reconnect both ends of the starter wire while soldering the thick VIOLET (A) relay wire to it and wrap the connection with electrical tape. © 2004 Directed Electronics, Inc. • BROWN (H1/3) wire on the main harness to it and wrap the connection with electrical tape. Do not use the vehicle until you confirm the operation of the brake shutdown. © 2004 Directed Electronics, Inc. • Do not use the vehicle until you confirm the operation of the hood pin shutdown. The bypass toggle switch is designed to bypass the remote start in an emergency or to disable the remote start functions © 2004 Directed Electronics, Inc.

• If the web vehicle information suggests a different type of parking light circuit, please contact BOA Technical Support. TO GRAY (H1/5) WIRE CONTROL MODULE BYPASS TOGGLE SWITCH BYPASSED WHEN CLOSED © 2004 Directed Electronics, Inc.